Normally installing film can be difficult and painstaking experience but our system has removed the most difficult steps of pre-cutting the film and buying expensive installation tools. Watch the installation preview to see how easy it can be to Sun-Chek your windows.

There are six factors affecting fabric fading:

1. Ultraviolet Light
2. Visible Light
3. Heat and Humidity
4. Chemical Vapors (including ozone)
5. Age of Fabric
6. Dye Fastness

Clear single pane glass (1/8" to 1/4") will reject 23-28% of the ultraviolet light from the sun. Insulated glass is slightly better, rejecting 36-41%. Window films installed on glass reject 95-99% of solar ultraviolet light.

Different types of clear glass and window systems will reject 13- 29% of the solar heat. With window films, 80% solar heat rejection can be obtained.

No window film can eliminate fading. It can, however, offer maximum protection from fading due to solar ultraviolet light and solar heat.

The effective life of window film will vary by the type of film, type of glass, window construction, compass orientation of glass, and in which part of the world the building is located. There are documented cases of film lasting 20 years or more in some instances, however, the average life span for film here in North America would be 12-15 years.

Windows with film applied are easily cleaned without damage to their appearance as long as a few common-sense guidelines are followed:

1. Use a soft clean cloth, soft paper towel, or clean synthetic sponge.
2. Use a soft cloth or squeegee for drying the window.
3. Use any normal glass cleaning solution which contains no abrasive materials.

The availability of scratch resistant coatings as a standard feature of quality films has virtually eliminated the need for extra special precautions in cleaning.

In most cases if a house plant is already receiving adequate light the use of window film will not harm it. New growth or flowering may be retarded, and, for a few days, a plant may go into a state of shock while it adjusts to the light change.

If a particular plant normally wilts by the end of a sunny day, it will actually thrive better with film installed. Although there are some obvious guidelines in determining what, if any, effect window film will have on a plant (for instance, dark green plants need less light than lighter colored ones), there is one sample test which can be done prior to film installation: merely move the plant to an area with less sunlight for a few days. In addition, most nurseries or local agriculture agencies can advise you whether a particular plant needs closer to maximal or minimal light.

Whether window film should be used on low E windows and how much you will benefit depends on three factors:

1.Type of low E surface used on glass
2.Location of low E surface in the window system
3.The desired amount of heat gain reduction, heat loss reduction, or other film benefits.

There are two basic types of low E surfaces on glass. One of these is a conductive coating put on glass as it is being made. It gives some heat loss reduction, but does little to reduce heat gain into a building. The second type is a more complex system of multiple layers of metals and conductive coatings deposited on glass after it has been made. This type of low E glass gives heat reductions of 30% to 50% in addition to reducing heat loss. Obviously there will be more heat gain reduction using film on the first type. If there is any question about the type you may have, ask your glass company or the window manufacturer to send you the specific information about your glass.

The location of the low E surface in your window system is also very important in deciding whether film should be used. If the low E coating is on the room-side surface of the innermost pane of glass, the use of window film may reduce or eliminate the heat loss reduction of the glass itself. This may be more than offset by the heat gain reduction/heat loss reduction properties of the films to be used. Most low E window systems,

however, consist of double pane windows where the low E surface faces the air space between the panes. In this case, film can be installed without eliminating the heat loss reduction benefit of the low E glass. The type of window film you choose for low E glass depends entirely on your desired benefit -whether you want to reduce heat gain, control glare, prevent heat loss, reduce fading or enhance the safety of your windows and glass doors. Carefully consider all these benefits before making a final decision.

Glass breaks when stressed. There are five types of stress which may cause glass breakage:

1. Thermal Stress--from absorption of solar radiation
2. Tensile Stress--from the weight of the glass itself
3. Mechanical Flexing Stress--from wind
4. Impact Stress--from flying objects, hail, baseballs
5. Twisting Stress--from building or window frame sagging or settling

The first type, thermal stress, is the only one which film may affect. The use of window films will increase the thermal stress on sunlit glass. However, there are also other factors which will increase thermal stress such as: partial shading of windows from overhangs, tightly fitting drapes or blinds, signs or decals on windows, heating and cooling vents directed at glass. In addition, different types of glass (annealed versus tempered, clear versus tinted) have different solar absorption rates and will withstand different degrees of thermal stress.

The window film manufacturers have recommended film-to-glass tables for use by factory-trained dealer installers. If a consumer is ever in doubt, he/ she should request a copy of such guidelines. Listed are some glass types or conditions where the use of a solar control (not clear safety) type of window film is not recommended without extreme caution.

SINGLE PANE GLASS LARGER THAN 100 SQUARE FEET
DOUBLE PANE GLASS LARGER THAN 40 SQUARE FEET
CLEAR GLASS THICKER THAN 3/8 INCH
TINTED GLASS THICKER THAN 1/4 INCH
WINDOW FRAMING SYSTEMS OF CONCRETE, SOLID ALUMINUM, OR SOLID STEEL

GLASS WHERE SEALANT OR GLAZING COMPOUND HAS HARDENED
VISIBLY CHIPPED, CRACKED OR OTHERWISE DAMAGED GLASS
REFLECTIVE, WIRED, TEXTURED, OR PATTERNED GLASS
TRIPLE PANE GLASS
LAMINATED GLASS WINDOWS